The door seal acts as a seal between the drum and body of the washing machine. When the door is closed, a tight seal prevents water leaks while the washing and spinning cycles are in progress. This is the band that holds the seal firmly in place. As the most important part of keeping the door deal in place, this retaining band can be particularly difficult to remove. They are slightly different from the outer band, and generally have a screw or nut holding the spring in place. Replace the door seal on your washing machine if you notice any signs of wear, damage, or leakage. The door seal becomes stiffer, wears down, or develops rips. It traps the water inside the machine, preserving its efficiency and protecting your laundry space from possible water damage. What damages the door seal? The door seal acts as a barrier between the drum and the outer casing of the washing machine. Water is prevented from leaking when the washing and spinning cycles are in progress by the door's tight seal when it is closed.

Wipe away any excess grime from the drum and the inside of your washing machine door. Lubricate the seal Align the drainage holes at the bottom of the seal with the holes in your machine door. Install the inner spring/band This causes water leaks throughout the washing process, which may injure your floors or the area around the machine's and reduce its functionality. How do you replace the door seal on a washing machine? Now you’re aware of what is causing the issue within your appliance, it’s time to get started on how to replace the door seal. There are several ways that you can go about this. Some models of washing machines are easier to fix than others, but this guide will show you how to replace a washing machine door seal for almost any model.This washing machine door seal is a genuine Indesit washing machine spare part. It also fits Balay, Constructa, Neff, Pitsos, Profilo, and Siemens washing machines. How to Fit a Washing Machine Door Seal

Over time, the washing machine's functionality is decreased and your flooring or the area surrounding it may be damaged. How do you replace the door seal on a washing machine? Now the hard part is out of the way, it is time to unfold the seal onto the outside of the drum. Refit the outer retaining band to hold the seal in place. Install the final pieces With your newfound knowledge in mind, ensure that you have all the correct pieces that your model requires. Following this guide for how to replace a washing machine door seal, it should be relatively straightforward. If your washing machine does not allow you to remove the front panel, then there are a couple more options that can make the replacement process a little easier. Note their position, as your new seal will have similar holes for drainage that need to be installed in the same place in the machine. Remove the seal

How to replace a Washing Machine Door Seal:

This can be more difficult than removing the spring. As some models age, the inner spring can tighten and be difficult to loosen. If this is the case, persistence and perseverance are key to fitting the inner spring. Holding the tightening screw or nut in place at the top, inch the rest of the band onto the lip using a flat head screwdriver to fit the new door seal. Fit the new door seal Lastly, it is time to reattach all the parts you initially removed to access the door seal. Some appliances do not require the need to remove the front panel or lid, but it is advised for ease of access to the internal of the machine. Expert Tip: One of the most common reasons for breaking seals is an accumulation of dirt within the gap between the door and frame. To prevent this from happening in the future, you may want to consider using a vacuum in between uses to gather up old tissue and debris from your door seal.

Please note that the following video will give you a guide on how to fit this part, however the exact fitting may differ depending on your make and model. Ensure the top of the washing machine is unscrewed and removed, to give you direct access from the top opening of the washing machine. Using a screwdriver, loosen the nut or screw of the tension band to remove the seal. Starting from the bottom, slide a flat head screwdriver beneath the spring and slowly and gently pry the spring from the drum. Find the drain holes on your old seal Some new seals come pre-lubricated. If not, you can use a little dash of washing-up liquid to help replace your door seal. Place the new door seal over the drumMost door seals are fitted with a plastic retaining spring or band that will need to be removed away before the seal can be removed. Using a flat-head screwdriver, pry away from the around the rim and pull entirely off the seal. Some appliances may not have an outer spring on their door. If this is the case, your job should be a little easier! Fold the door seal into the washing machine