Equal Angle Steel Bars - These long ‘L’-shaped mild steel bars are used across a wide variety of construction projects and offer further structural support. Tongue-and-groove One side and one end of the plank have a groove, the other side and end have a tongue (protruding wood along an edge’s center). The tongue and groove fit snugly together, thus joining or aligning the planks, and are not visible once joined. Classic oak 260 tongue-and-groove flooring can be installed by glue-down (both engineered and solid), floating (engineered only), or nail-down (both solid and engineered). Parallel Flange Channels (PFC) - Otherwise known as C channel beams, PFCs can massively add to a building’s stability and are usually used in structural steel fabrication projects.

Universal Columns - Also known as H beams, the differences in their design compared to steel beams make them perfect for use as vertical supports.At Steel Beam Suppliers, we understand how vital it is for your building’s structure to be completely safe, no matter how large or small the project scale. Universal beams may even be considered as the bones or skeletal structure of a building, which is why we ensure that they are of the highest quality standards, including the EN10025 standards. Universal Beam vs. Universal Column Tyres Marked like above have four components. The first number is the width of the tyre. The second is the height of the sidewall and the third is the rim diameter. The "-" again means the tyre is a crossply. all figures are in inches. We do NOT decide if an item is or isn’t exempt & we don’t make any more or less money if we charge you VAT or we don’t charge you VAT. The inner tube size you require will depend on the size of tyre being used. The size of the tyre is often written on the sidewall, and a inner tube to fit this size range is required. Because inner tubes are very flexible they can fit a range of tyre sizes, expecially larger inner tubes. A inner tube will fit a range of tyres sizes, which is often printed on the tube but not always. Sometimes only the base tube size is printed on the tube (3.50-6) but it is still ment to fit a range of tyres sizes.

Engineered wood flooring consists of two or more layers of wood adhered together to form a plank. Typically, engineered wood flooring uses a thin layer (lamella) of a more expensive wood bonded to a core constructed from cheaper wood. The increased stability of engineered wood is achieved by running each layer at a 90° angle to the layer above. This stability makes it a universal product that can be installed over all types of subfloors above, below or on grade. Engineered wood is the most common type of wood flooring in Europe and has been growing in popularity in North America Oil – Oiled floors have existed for several thousand years and is the most common floor finish used globally. Oils used for floor finishing are natural drying oils of vegetable origin that are not to be confused with petroleum based oils and contain no VOCs. Pre-finished oil floors can be UV cured. If you require universal steel beams fabricated to the highest standard, then you’ve come to the right place, as they can be utilised for all manners of construction purposes, including those for large commercial premises and residential properties. The railways and bridges you see from your office or hotel window most likely have high-quality universal beams at their core.

Universal Beam vs. Universal Column

Brushed and oiled – Steel brushes are used in the direction of the grain which opens up the surface of the wood and removes splinters. The wood is then oiled.

Classic oak 260 unfinished boards are made up of classic grade boards with some blemishes and small knots. This type of floor will give you a very traditional look. Plank Width Also known as I-beams or H-beams, RSJ steel beams are built by rolling a single piece of structural steel. This helps to maintain their structural integrity and are ideal for supporting walls and floors where the underlying requirement is building an extension or creating an opening in a load-bearing wall. Hollow sections (RHS, SHS, and CHS) are available in metric sizes which are common both in the UK and across the continent. Hot finished hollow sections are supplied in accordance with EN10210 and in EN10219 for cold formed hollow sections. Although the sections dimension may be identical for both hot finished and cold formed, the capacities are not direct equivalents so care is required to ensure the correct grade is requested. If you fail to return any VAT exemption forms to us we WILL charge your card for the outstanding VAT. Mild Steel Bars - Strong and dependable, these are solid pieces of steel that come in a wide variety of shapes and dimensions depending on the needs of your project, including flat, round and square bars.

There are a few ways for giving the size of tyres. Measurements given in inches and sometimes in millimetres or both. We have shown some examples below to help you recognise the size markings on your own tyre.

If you’re ready to benefit from quality fabricated steel, here are the products that are available to buy through our online store. For open sections, although the grades are standardised across Europe the sizes are not. In the UK sections are generally produced according to BS 4-1:1993, which converts imperial sizes to metric (26″ becomes 914mm), whereas on the continent the dimensions are truly metric. Inner tube sizes and valve types. This guide gives a basic description and purpose of the most common types of inner and valve shapes.Important Note: It does NOT include a frail elderly person who is otherwise able-bodied or any person who is only temporarily disabled or incapacitated, such as with a broken limb. In the UK we use the terms UB (Universal Beams) and UC (Universal Columns) whereas continental beams are I Sections (IPE etc) and columns are H Sections (HEA etc).