Note: Compared with the RJ45 Console cable and USB-to-RS232 cable, it might be more difficult to enter the BootUtil with a Micro-USB cable. If you still cannot enter the BootUtil after several attempts, you may get a USB-to-RS232 cable. Note the Ethernet port type in the command is the native speed mode of the ports, not the current operating mode. For example, assuming the current speed mode of SFP+ port 25 is 1Gbps, to configure it, the command should be “interface ten-gigabitEthernet 1/0/25”, or simply “int te 1/0/25”. Feature Filter: Tutto Configuration Guide User Application Requirement Further Assistance Troubleshooting When You Set Up FAQs

What's the difference between the Master Administrator, Administrator and Viewer accounts in the Omada Controller? 04-12-2023 16282 How to enter the BootUtil Menu to factory reset the switch with the console cable? 09-06-2021 78714Please note: The products of TP-Link partly contain software code developed by third parties, including software code subject to the GNU General Public Licence (“GPL“), Version 1/Version 2/Version 3 or GNU Lesser General Public License ("LGPL"). You may use the respective software condition to following the GPL licence terms. How to configure IGMP Snooping for IPTV network on L2 Managed switches using the new GUI 06-27-2022 139402 Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. ( Normally Vx.0=Vx.6/Vx.8 (eg:V1.0=V1.6/V1.8); Vx.x0=Vx.x6/Vx.x8 (eg:V1.20=V1.26/V1.28) How to Configure Management VLAN on TP-Link Smart and Managed Switches Using the New GUI 05-18-2023 25766 The CLI is divided into different command modes: User EXEC Mode, Privileged EXEC Mode, Global Configuration Mode, Interface Configuration Mode, and VLAN Configuration Mode. Interface Configuration Mode can also be divided into Interface Ethernet, Interface link-aggregation, and some other modes, which are shown in the following diagram.

The switchport general allowed command is used to add a port to a VLAN and set the tagged/untagged mode. To remove a port for a VLAN, please use no switchport general allowed command.This guide is intended to provide network administrators with some typical examples of CLI (Command Line Interface) configuration. The switch supports configuring IGMP Snooping on a per-VLAN basis. After IGMP Snooping is enabled globally, you also need to enable IGMP Snooping and configure the corresponding parameters for the VLANs that the router ports and the member ports are in. The command is “ip igmp snooping vlan-config vlan-id”. V1: 1582.49 BTU/h (110 V/60 Hz) (with 384 W PD connected); 105.78 BTU/h (110 V/60 Hz) (no PD connected) For example, to enter the show command, you can type “ sh”, then press the TAB key, or type a question mark immediately afterward, like “sh?”, then the switch will automatically complete the interface command. Note that the question mark will not be displayed.

Use the interface or vlan command to enter this mode from Global Configuration Mode, which allows doing configurations for the specific port(s). V2: 1589.31 BTU/hr (110 V/60 Hz) (with 384 W PD connected); 117.38 BTU/hr (110 V/60 Hz) (no PD connected) What should I do when the Omada Software Controller (V4) fails to discover the devices? 11-23-2021 87590 Come gestire i dispositivi Omada in diversi siti utilizzando il Controller Omada SDN via VPN (Controller 5.0 o successivo) 05-02-2023 17174

Note that TP-Link switches use Auto duplex mode by default and it is recommended to keep the mode if there are no connection problems. Ports 2, 3, 4 are used as access ports to connect computers. The following configurations describe how to add port 2, 3, 4 to the corresponding VLANs and set PVIDs. After entering part of a command, you can press the TAB key or a question mark (?) then the switch will automatically complete the command. If your input corresponds to more than one command, the switch will not auto-complete but will display all related commands. Using Omada controller to configure multiple SSIDs with different VLANs on TP-Link Omada EAPs and Switches to work with a non-Omada gateway(Multi-Net NAT supported) 07-07-2023 17569 Qual è la differenza tra gli account Master Administrator, Administrator e Viewer in Omada Controller? 04-14-2023 16282