Top Tip: Struggling to keep the line straight as you draw? Try just making small marks at regular intervals on the wall in line with the string and then use the straight edge of your spirit level to join them up. Step 2 Sometimes goods can be delivered in multiple deliveries, this is due to some items coming direct from suppliers or our own yard. If this is the case, multiple charges will be combined at the basket. Now you are ready to fit your first length of downpipe. Working from the outlet (or offset bend if you have one) down towards the drain: The deliveries below are for mainland UK, for Highlands, Channel and offshore islands an extra charge per consignment will be applied as below, we can also arrange Saturday delivery at extra cost.

My neighbours house has plastic guttering along one side, supported about every 6' (1.8m) and it's saggier than - well, let's not finish that simile! You need to support plastic guttering much more frequently, as folks above have said. My neighbours guttering pours water down his wall every time it rains heavily, the weight of the water makes it twist. Installing new guttering may seem a little daunting at first, but, with the right help and proper planning, it’s a job that even a novice DIYer can successfully complete. In this handy step-by-step guide, we’ll walk you through everything you need to do to install your guttering from start to finish.Using a drill with an appropriate masonry drill bit (follow the size recommendation given by the guttering manufacturer), you can now drill the fixing holes you marked and fit them with appropriate wall plugs ready for attaching your pipe clips. If your gutter runs around the edge of your building, you will of course need to install a bend instead of a stopend here. The methods used thus far can be repeated for any additional fixings or lengths you need to install. Just remember to fit the stopend to the last length of gutter to complete the run. Note: If you are using a running outlet that is positioned more centrally along the run, you will need to repeat this process at both ends of your roof to ensure that all the gutters flow towards the outlet with the correct fall. What if you don’t have a fascia board? Brett Martin’s rainwater systems have been successfully tested for accelerated ageing in accordance with BS EN 607: 1995. The manufacturer guarantees the colourfastness ofwhite rainwater systems for a period of ten years, from date of manufacture. Full warranty detailsare available on request from Brett Martin Ltd. The cast iron effect stuff I don't think looks very good, the guttering joints especially. If you want to go for plastic then personally I'd just go for ordinary plastic and be done with, save yourself some money.

Now all you need to do is take good care of your new system and you should be able to enjoy many, many years of hassle-free gutter ownership. But don’t worry, we aren’t about to abandon you here to fend for yourself. We’ve written a DIY gutter maintenance guide that’s specifically designed to help you secure that hassle free gutter life. Brett Martin’s Rainwater systems have been fully tested for accelerated ageing in accordance with BS EN 607:2004 and the excellence of Brett Martin Rainwater systems is recognized through the company’s achievement of BS EN ISO 9001:2015. You can be confident that,as a BSI Registered Firm, Brett Martin's Quality Assurance programme guarantees that Brett Martin’s Rainwater is a first class product. Does the plastic Cascade range fit into exsisiting Cast Iron Guttering? They also do a rectangular steel gutter - could you fix it directly to your wall with some spacers? Not ideal, but should be quite strong over a span. Top Tip: If you are using a cordless screwdriver, or a drill with a screw bit, try dropping the speed/power setting as low as it will go to help you avoid over-tightening the screws. Step 3 The first thing you need to do is to establish the position of the outlet that will connect to the downpipe (whether that be a running or stopend outlet). Alright, so this isn’t exactly the beginning of our guttering, but it should always be the beginning of your installation, as it is one of the most important pieces to get positioned right. Here’s how to do it:

Standard Delivery

Please note the image shown below is just an example and a colour swatch is recommended to show true representation. Once the resin has set and the gutter pin is secure, attach your string line to the gutter hangers to create a guide line. Adjust the gutter hanger up to the guide line by tightening the nuts between the wall pin using the spanner. Half Round Cascade Guttering and 115mm Deepstyle Cascade Guttering is compatible with 68mm Round Cascade Donwpipe or 68mm Round Corner Cascade Donwpipe The first thing you need to do is to mark a 90-degree vertical line down the wall where the centre of the downpipe will be to help guide your installation.

Prostyle Cascade Guttering is compatible with either 68mm Round Cascade Donwpipe or 65mm Square Cascade Downpipe Okay, so, you’ve bought all your guttering parts and pieces, lined them all up in an obsessively neat fashion on the ground (no...just us?), and gathered together all the tools you will need. Now you just need to know where to start. Well, we hear the beginning is a very good place, so let’s start there with Step 1. Step 1 Colours displayed are not NCS and/or RAL colours. Swatch samples can be supplied to demonstrate true colour. Internal Stop End External Stop End What is the difference between an external and internal gutter angle?Your other option, which avoids all the problems with plastic creaking and joints coming loose (both of which drove me mad in a previous house) is coated steel guttering, like Lindab rainline. I used some for the sides of a dormer where the only way to access it to repaint it is to get scaffolders in, i.e. I didn't want to be up there again for many years to come. It's good stuff - prefinished, fairly light, easy to fit, much stronger and less creak-prone than plastic. Next, you need to fix the outlet in place as this will help you establish the positioning of the rest of the system. Like we said earlier, it isn’t essential to install with a fall, but it is something we highly recommend and, as such, it will be part of our step-by-step guide going forward. How to fit new gutters Please note when using the 112mm half round, 115mm deepstyle and 170mm industrial gutter systems are used the stop end are universal, but when using the 106mm prostyle range you will need to use left and right handed stop ends. If you are placing them at 400mm apart, the calculation would be 400/350 which equals 1.14mm (round down to 1mm for easier measurements).