Waterproof Silicone Flexible Heating Pad 60*60MM DC 12V 10W

£9.9
FREE Shipping

Waterproof Silicone Flexible Heating Pad 60*60MM DC 12V 10W

Waterproof Silicone Flexible Heating Pad 60*60MM DC 12V 10W

RRP: £99
Price: £9.9
£9.9 FREE Shipping

In stock

We accept the following payment methods

Description

Precise and flexible heat distribution plays a crucial role in many applications where temperature control system for heating, warm and frost protection in drums, cylinders or hoppers machinery is invaluable in heating technology. In the jungle of different wire mats available on the market, it could be a time-consuming exercise to find the right silicone heaters for your project. We have a solution to this problem as our dedicated, carefully selected heaters offer high-quality while keeping your budget under control. Maybe I don't even need the heating pad after the plywood and foam insulation is added raising the batteries off the cold steel floor. Heat is never an issue, in 4.5 years I've only seen a cell at 80f and that has only been twice. 45-75f is the normal cell temp range depending on season and location. Strip the positive and negative wires from each pair. Once you have stripped all four wires coming out of the heat pad and the additional four wires from the temperature sensor, you are ready to move on to the next step.

Heating | DC GUY, Power To The People - For Less DIY Battery Heating | DC GUY, Power To The People - For Less

Grab your 4-prong push-in wire connectors. Plug the two white (positive) wires from the temperature sensor into the first push-in wire connector. Even charging is a low C rate, .12c is max with solar, .16c is max the panels can produce but there are always loads. If the generator is needed for a boost charge then .2c (100a) is what I'll set the charger to.

I have no experience with this pad maybe someone else does or installed something similar. It has a built-in thermostat that is set to turn itself on at 45°F( + - 5 degrees) and turn itself off at 68°F( + - 5 degrees). As long as the on/ off switch is in the on position.

Heater Mats, Standard Sizes, Custom Design Silicone Rubber Heater Mats, Standard Sizes, Custom Design

Note: R egarding the Standard, Large and Giant Heat Pads listed here they are not 12v they can’t be used with a car adaptor in a vehicle) The heat pad carries about 15W per side, so 14- or 16-gauge wire is typically recommended for extra wire length.For this modification, you’ll need the following components available mostly through our friends at Expion360 who designed and tested this system for their excellent VPR PowerMod 12 volt Lithium Battery: Additionally we don’t recommend these pads for use in Veterinary centres. For this our recommendation is either the Flexiguard 44 or the Flexiguard 55. The first step, as with any installation, is to confirm that you have the right equipment. Eric, one our expert sales technicians, walked us through the process of setting up a heat pad with our batteries.

Lithium Battery RV Heating System Mod - Truck Camper Adventure Lithium Battery RV Heating System Mod - Truck Camper Adventure

It is worth to note that control of the temperature should always be in place, and the safety margin applied as the maximum peak temperature for this silicone part should never exceed +300°C. The heating pad can be connected to the 12v fuse panel with a switch added inline to turn it on/ off if needed. Power consumption should be roughly 6a which would be a little more than 1% an hour of my battery bank, I'm thinking it probably wouldn't need to be used more than an hour or so periodically.The ambient temperature sensor should be placed in between the adhesive side of the heat pad and the item wished to be heated (in this case, between the heat pad and the battery). Our heat pads come equipped with an ambient temperature sensor. The ambient temperature sensor sits between the battery case and wiring harness, allowing the heat pad to only be turned on when below 35°F. Once the ambient temperature sensor reaches 35°F, the switch is enabled, allowing current to flow to the heat pad. Our Battle Born Batteries ship with 18-8 stainless steel 5/16 – 18 1” and 1 ¼’ bolts, brass washers and 18-8 stainless steel nuts with nylon inserts.



  • Fruugo ID: 258392218-563234582
  • EAN: 764486781913
  • Sold by: Fruugo

Delivery & Returns

Fruugo

Address: UK
All products: Visit Fruugo Shop