Jaegerndorfer (Jägerndorfer) are manufacturers of scale model trains, cable cars and associated accessories. The models they produce, while not as cheap as some other options, are serious pieces of kit. A Jägerndorfer cable car will take your Christmas village display to a whole new level.

The kit arrives in a very long and quite deep box with several pictures of the Graf Zeppelin on the front and sides. Even though it measures out at 38.5" or 97.8cm long there are very few parts, the two hull halves and a single sprue of quite hard white styrene, one sprue of nylon, apparently. There is also a single clear styrene part and a sealed bag for the included lighting equipment. Detail is naturally quite sparse by the very nature of the airship. The longerons of the hull and fins are quite prominent, perhaps a little over emphasised, but should look ok given a slight sanding down and under a coat of primer and Alclad or similar, in fact the kit is so big it might be better just to go to Halfords and get various shades of silver auto paint. There were apparently shape issues with the older kit and even though it says new tooling on the box there really isn't any evidence of this, so the incorrect cross-section is still there. The nylon parts are also pretty awful to work with whether gluing or filling so beware. Using the locator holes for the still omitted gun platform, I inserted a sturdy wire hooked at one end and suspended the model from my workshop ceiling for easy painting. I airbrushed the envelope with mixes of Tamiya Buff (No. XF-57) and Desert Yellow (No. XF-59). When the paint had dried, then the gun platform went on without any trouble. I assembled both gondolas as seen in steps 2 and 10 and added the PE supports to the hull underside inserts (parts E1 and E2). Carefully, I attached the gondolas. Despite my gentleness, I lost or broke a couple of tiny PE parts for the front gondola and replaced them with .020-inch styrene rod. After I glued the inserts into the hull with all of these structures in place, I used extreme care to attach the PE rear propeller supports.The videos below show Jägerndorfer cable car models in use within a village display, the first is 1:87 scale and the second is 1:32.

The Graf Zeppelin had a career spanning nine years, and in that time made 590 flights and carried over 34,000 passengers without incident. She also carried out the first commercial and scheduled flights across the Atlantic, first around the world and even flew a scientific mission over the North Pole. This is certainly and interesting and impressive kit, if purely for its size. The hull problems cannot be easily sorted, but with the addition of some brass rod and strut it could be made into a good looking model and will look impressive, whether hung from the ceiling or or the stand provided, although a better one would be preferable. I can recommend it purely as something different, baring in mind the problems mentioned above. Whilst not the most aerodynamically efficient design it did incorporate one interesting feature, in the fuel used for powering the five Maybach VL-2 12-cylinder engines, which could develop 550hp at maximum revolutions, and 450 hp at 1400 RPM in cruise. This was the use of Blau Gas which had the same density as air so wouldn't upset the balance of the airship as the fuel was used, unlike more conventional fuels such as paraffin and diesel. This also gave the airship an extra 30 hours of flying time as the lifting Hydrogen gas didn't need to be expelled to keep the airship at the correct altitude. The use of Blau gas allowed the Graf Zeppelin to stay aloft for over 100 hours.The main gondola is a three piece item, the gondola, a clear insert, which is actually very clear, and the gondola bottom. Into the gondola are the pilots controls station and a number of comfy chairs. It also houses the lighting cct. lights, switch, and 3v coin cell battery all included. The internals all fitted, painted and in the case of the lights, tested, the gondola is fitted into place. There is a small bumper parts that is then added to the underside. There are one of the girders, framework and other fittings that are visible in the real Graf Zeppelin in the gondola which is shame, but some enterprising modeller should be able to scratch build this if they like. Landscaping Cable Cars, Department 56, Gondolas, Jaegendorfer, Jagerndorfer, Lemax, Luville, Mr Christmas, Ski Lift, St Nicholas Square, Trains. permalink. Construction is very simple, much like the instructions which leave a lot to be desired. The hull halves have very large location pins and holes and they do give a very positive fit, (not shown in the photograph above, as I wanted to get it apart again), although it will still need some careful gluing and an extensive seam removal session. There is a small conical nose piece that's fitted to the bow. The four tail fins are each made of two halves and locate well into their slots. Again the longerons may need sanding down a bit. Unfortunately the balance horns, on the nylon sprue are completely the wrong shape, rather than being teardrop they should be and aerofoil shape. There are pictures of these on the interweb amongst many others than would prove useful for this build, or at least show up how many other problems there are in the kit. Deviating from the instructions, I assembled major body sections as seen in steps 1, 7, and 13, but left off the upper gun platform; why will be obvious later. I lightly sanded the seams between the hull segments.

The design and construction of Graf Zeppelin were essentially conservative, based on tried-and-true technology developed over the Zeppelin Company’s decades of experience, and the ship was constructed of triangular Duralumin girders, with frames spaced 15 meters apart. The design of the Zeppelin was constricted by the size of the building shed at Friedrichshafen, which had inner dimensions of 787 feet in length and 115 feet in height. Since greater size meant greater efficiency in long distance operation, the challenge for Ludwig Durr and his design team was to create a ship with the largest possible gas capacity that could be built within the confines of the construction shed. Thus the airship that was designed was a cylinder 776ft in length and 100ft in diameter. The gondola, which was slung under the nose of the airship meant that the height of the airship from the bottom of the gondola to the top of the hull was 110ft. The rest, as they say is up to the painting and getting the various shades of silver dope that is very noticeable on the real thing, not forgetting that this is a BIG kit. Takom deserves credit for releasing a kit that is both different and important in the history of World War I aerial warfare. Germany made extensive use of Zeppelin rigid airships for bombing and reconnaissance throughout the war, and Takom has kitted two of the most common classes, the P and slightly larger Q. I built the latter.

Specs

The center units that extend the hull for the Q-class ship were slightly larger in diameter than the other sections, so they needed more sanding. Fortunately, paint demarcation lines fall on the edges of the sections and help hide the disparity. That’s the easy part of the build done. The challenging part of the build began while fitting the gondolas and the rear engines. First, I rolled two hand towels and placed them on either side of the hull to keep it steady while adding these delicate parts. Graf Zeppelin was over the Canary Islands on the last day of a South American flight from Brazil to Germany when it received news of the Hindenburg disaster in Lakehurst, New Jersey. Captain Hans von Schiller withheld the news from his passengers, and told them of the disaster only after the ship’s safe landing in Germany.