INJORA RC Car Axles Set CNC Metal Front and Rear Straight Axle for 1:10 RC Rock Crawler Axial SCX10 D90 RC Car

Product Information

Most if not all of these parts are strictly dimensioned, so It would be better if you print them solid. For that, I'm using 0.4mm line widths and 0.2mm layer heights with hundreds of top/bottoms, so it gets solid. The use of a 4-link suspension system helps to reduce rear axle swing. A flawless bend allows for smooth operation and accurate handling throughout the suspension cycle. Remember, if you choose the medium length axles, you will have to apply symetry to one of the axle body parts to have them with the diffs aligned to the same side. Just for the Axial portion I think it would be simpler to list by axle designation since they use them on several rigs (AR44,AR45, AR60 etc)

There is a 2.2 canyon tire that i think you would like and it would looks a bit more scale with the model imo. They are wide and soft a bit smaller than an outlaw tire.I have actually tested both methods, and they are lasting at least all my first tests, which are a little aggressive :S

The Losi Night Crawler Kit is a rolling chassis that does not contain any electronics, battery, or charger. For ultimate DIY flexibility, add your own motor, electronic speed control (ESC), servo, and radio system to the chassis. However, if you want to take the chassis to the next level, you might consider adding a roll cage, which offers it an advantage in difficult terrain. I saw this kind of axles time ago, but they seemed something impossible for me then, especially when you have other parts of the transmission to improve to have a reliable build. Your portal axle is still an axle so it is unsprung weight so it really isn't like have weight other places. The added clearance allows you to run smaller tires with more clearance and lowering your overall CG. The MOA features the popular RC4WD Outcry Brushed Speed Controller with built-in drag brake and a separate 6V 5amp Turbo BEC to provide reliable and constant power any time you need it.The high-quality carbon fiber and delrin materials make these wheels super lightweight, while still providing ample strength to support the weight of the MOA crawler. I’m going to build a new rig for 2022. I have a class one,class two, and a sorta class 3. So now I want to make a rig that outperforms everything. A total cheater rig. So everything in the rules that is restricted is what this rig should have. With the medium length axles and big crawler wheels, the total width is around 290mm, 280mm with 96mm wheels. You can add or remove 24mm to those numbers if using the long or short axles.

The graphics are of exceptional quality and have a smooth, scratch-resistant surface. You may choose between a relaxed matte finish and a more opulent glossy finish. Designed to be an out of box competition crawler tire, the Bully 2.2 is created with the help of the RC4WD Crawler Team with full testing completed in multiple conditions and terrains.If you are going to mount your FMM there on that chassis like Dred805 has you motor will sit low. You will probably need an axle that is offset and a transmission to match. Not sure what motor mount you are using. The Night Crawler features a scale body with an Exoskeleton cage that protects it from the weather while maintaining scale accuracy and performance. The new Bully 2 Axles have spent years in research, testing and development to bring you a competition worthy axle out of the box. No need to spend countless dollars on upgrading these axles. Inside each wheel Hub a slight 12/13 reduction will occur. To attach the 12T gear to the CVDs you will have two possibilities:

I still use the Enduro chassis (my class 1) with AR44 axles. Because the pinon sits higher on those axles it was easier to get better drive line angles. I didn't like the Enduro chassis with the Enduro axles but I really like it with the AR 44s. Two have the Ar44 Axial, light weight good clearance and can turn tight. They are on light comp rigs, They are not the strongest and maybe not the best for trail but I am a non aggressive driver and like them for comp. One is Class 2 and the other is class 1. Specially for the gears, you will need a very high inter-layer adhesion, so probably warm up 5 or 10ºC your PLA for the best adhesion and adapt the inner walls width to perfectly fill all the inside of the part.Waterproof Electronics : A core part of serious off-roading is taking on puddles, rivers and streams, so your electronics need to be prepared for this.