Facom 006105 Mechanical Grease 200g

Product Information

General-purpose grease (also known as GP grease) is formulated to serve various purposes, including most industrial and domestic uses. It consists of base oil with a medium viscosity index. It provides decent water and dirt protection but isn’t very long-lasting. Typically, a Grade 2 grease is employed with a base oil viscosity in the 150 to 220 cSt range at 40°C (104°F). Higher viscosity base oils, EP additives and solid additives are used for low speeds, high loads and high temperatures. For bearing temperatures above 70°C (158°F), grease life (L) in hours tends to drop by a factor of 1.5 for each 10°C (18°F) increase in the following pattern, also shown in Figure 11,3: Insufficient lubrication can cause many problems for most passenger cars, including excessive engine noise, rust buildup, and excessive engine wear. Due to its high resistance to friction, moly grease isn’t recommended for fast-moving metal parts like roller bearings since this grease would slow them down. 3. Lithium Grease

Use of ozone depleting substances in laboratories. TemaNord 2003:516. "Archived copy" (PDF). Archived from the original (PDF) on 2008-02-27 . Retrieved 2011-03-28. {{ cite web}}: CS1 maint: archived copy as title ( link) It’s specifically recommended for high-pressure and heavy-duty applications since — unlike engine oil — it retains all of its properties under pressure and doesn’t lose shape.

7 PAHs on the EPA’s Priority Chemical List

On the other hand, low viscosity greases are ideal for high-speed engine parts. 4. Pressure And Temperature Performance

Section 6 - The accidental release measures offer recommendations on the appropriate response to spills, leaks or releases, including containment and cleanup practices to prevent or minimize exposure to people, properties or the environment. This section may also include recommendations distinguishing between responses for large and small spills when the spill volume has a significant impact on the hazard. The linear oscillatory friction tester (SRV) oscillates a steel ball on a disk while continuously recording the friction coefficient. Test frequency, stroke, temperature and specimen material and shape can vary to simulate field conditions. Limiting load at seizure is a useful measure of the EP and antiscuffing property of the grease. Grease is exposed to pure oxygen at 110 psi at 99°C in a "bomb" for 100 to 500 hours. A decrease in oxygen pressure provides a preliminary indication of grease life in extended storage, prelubricated bearings and in high-temperature service. Maximum pressure drop in the bomb may be specified in the range of 3 to 25 psi in 100 hours, and 25 to 50 psi in 500 hours. For this reason, it is important to weigh each property’s significance relative to the intended applications to select the best overall fit.For machinery which is operating in harsh conditions, or in dangerous and hard to reach locations, performing maintenance can be risky. Relatively specific, copper powder is mainly used for the assembly and protection of elements subjected to very high temperatures. It is also dielectric and hydrophobic, which makes it perfect for protecting connectors and live terminals. Tire grease This worked penetration is the basis for the consistency classification in Table 1 developed by the National Lubricating Grease Institute (NLGI). Also listed are the approximate yield strength and corresponding self-supporting height to be expected for grease in each penetration range. If you prefer a machine to do most of the work for you or you have a large area of carpet to clean, you’ll probably want to use a carpet cleaner. Store-bought cleaning solutions can get pricey. Here are some recipes for a DIY carpet cleaning solution for machines that can be used to clean grease from the carpet. Carpet Cleaner for Synthetic Carpets Section 2 - Hazard(s) identification includes the chemical’s hazards and the appropriate warning information associated with those hazards.

Thermal Run-away. Too much grease in a bearing, mechanical conditions (misalignment, excess preload, etc.), and starvation can lead to high running temperatures. This is most commonly associated with over-greasing, causing high heat from churning. In such cases, the dropping point is reached, the bearing begins to bleed, the grease runs dry and eventually failure occurs. Figure 2 shows an example of such a bearing. Devices like the UE Systems OnTrak SmartLube can help you avoid this issue by lubricating your bearings with the right amount of grease at the right time. The ultrasound technology measures friction in the bearing continuously—when grease is needed, the operator simply receives an altert on the cloud-based system and is given the option to lubricate the bearing with a push of a button. Constant-level lubricators are used mainly with enclosed bearings and gear trains that rely on a certain level of oil in the enclosure to stay properly lubricated. The external lubricator senses when the level in the enclosure drops and adds an appropriate makeup amount. These systems are usually unpowered and incorporate transparent oil reservoirs that must be topped up from time to time. Multi-point lubricatorsPassing indigenous bacteria (entrained in effluent) through the magnetic fields alters the cell walls permitting the absorption of mineral crystals. Filter life is also extended with co-operating magnetic water treatment, i.e. slime build-up is reduced. This is attributable to the consumption of polysaccharides by the magnetically affected bacteria. Accumulation of algae downstream is inhibited by virtue of the organic and inorganic matter having been bio converted. Because many journal and thrust bearings need a greater lubricant supply, grease cannot always meet their lubrication needs. Grease is not an option for the bearings of a large steam turbine-generator in a power house that requires more than 1,000 gallons per minute of oil for cooling and lubrication. On a smaller scale, grease is also incapable of supplying the needs of sleeve bearings in either automobile engines or industrial electric motors and their associated equipment. E.R. Booser, Life of oils and greases, in Tribology Data Handbook (CRC Press, Boca Raton, 1997), pp. 1018–1028 Section 12 - The ecological information provides information to evaluate the environmental impact of the chemical if it were released to the environment.