SOK Battery 100Ah 12V LiFePO4 Lithium Iron Phosphate Deep Cycle Battery,Perfect for Your RV or Any Off-Grid Applications,Low Temperature Disconnected.

Product Information

This manual is not a substitution for proper training. The intended use of this manual is to provide guidance and reference for the use of products sold by and associated with Current Connected, LLC. All materials mentioned in this Training Manual range in technicality and require varying competency levels and expertise. Therefore it is recommended to seek proper training before using products seen and mentioned in the training manual. Ensure all batteries are in the “BMS-OFF” state prior to installing the cable(s) as explained in the shutdown procedure. After the cable(s) have been installed, power up the system per the proper pre-charge procedure. If the battery is not detected by the Cerbo: UL 9540 is a safety standard for an energy storage system (ESS) and equipment intended for connection to a local utility grid or standalone application. It designates key issues associated with ESS. UL9540 certification is currently in progress. The time for completion is not currently set in stone, but is targeted for mid 2023. UL 9540A (Fire) certification The SK48v100 is compatible with select inverters in a closed-loop configuration where the battery programs the correct operating parameters to the inverter via CANBUS / RS485 communication. While this mode of operation is usually the most simple and precise control method, it is not a solution for everyone.

This is their only large form factor 12V battery that has high charge and discharge rating, but also has low temp protection. Power on the BMS per the power-up procedure. The LED lights on the front panel should be illuminated. The initial balancing process is slow and typically takes about 10 to 15 charge cycles before perfect cell balancing has occured. Cells are considered perfectly balanced when the voltage deviation is within 30mv, as indicated on the cell voltages battery screen. Cell imbalances on brand new, fully charged batteries can reach as high as 250mv. This is normal and no cause for concern. The only time to worry is if there is a large difference at a state of charge between 95% ~ 5%. BMS Screen Display Most solar controllers require the PV source be disconnected prior to shutting down or disconnecting batteries. Similarly, best practice is to turn off all loads on an inverter prior to turning it off. Since every installation is different, we can’t anticipate which ansulary items you may have, and which devices must be powered off before disconnecting your batteries. We expect you to use good judgement and turn these devices off prior to starting this shutdown process. Procedure: Product that was used for applications other than which it was designed and intended for, including repeated engine starting

The downside is that when the BMS opens the MOSFET switches to protect the cells, some controllers will reduce the output to a float voltage since they detect that the battery is no longer accepting a charge (because they assume that a battery not accepting current is fully charged). As a result, balancing does not have time to be completed and capacity in the system is reduced due to cell imbalance. I have been in business for over 40 years, have dealt with hundreds of suppliers, and I can say I have never had a better experience. 100 star rating! For systems using only 1 battery, navigate to setting 11 (Maximum charge current) and set this parameter to 95A. This is the maximum charge current one single battery allows with a touch of margin for error. For multi-battery systems, this setting can be set no greater than 95*(number of batteries).

Absolutely! With no acid or venting, this battery can be installed in any configuration except for upside-down (terminals facing down). Who makes the SOK BMS? If you wish to make your own cable, use our pinout table which creates a cable that is bidirectional, meaning either end can be plugged into the Cerbo-GX or the battery while still preserving full functionality. When using the previous table or competitor’s cables, it will require certain ends be plugged into their corresponding devices. Connector #1 For those who live off the grid, have solar panels or want to start using renewable energy sources an SOK 100AH LiFePO4 battery is a great investment. UL9540 Certification (Pending): The certification process is currently in progress, providing added assurance of quality and safety. The SOK Battery SK48V100 is built to meet the highest industry standards. Plug in the RS232 programming cable. Make certain that the cable is fully inserted into the RS232 port.Each battery will add 95A to the charge and discharge current. In other words, if 5 batteries are connected, you would expect to see 475A in either field. If you are providing normal everyday charging with solar, that’s when it would be better to reduce the charge current closer to the target of 63A or less. Areas having more than 4 hours of sun exposure can charge as low as a 25A (C/4) rate and still reach a full charge while experiencing minimal wear. Absorption Voltage Yes! An added bonus is that this battery supports full closed-loop communication with ALL Sol-Ark Inverters. In fact this is the easiest inverter on the market to setup battery communications with.