Sentinel - X100 Inhibitor 1L, Market Leading Heavy Duty Central Heating Inhibitor, Protection Against Corrosion and limescale, ensures Maximum Heating Efficiency and extends System Life, Clear (88000)

Product Information

Thread the ½” female BSP adaptor onto the exposed male threads at the hose connection point on the ball valve. Use a spanner to gently nip up the adaptor to ensure a water tight seal. Clean dirty heating systems, protect against future issues and maintain system performance with Sentinel Rapid-Dose ®. Simplicity

Maintaining system health is essential for ensuring that it runs both reliably and in an energy-efficient way, working towards Carbon Reduction Commitment goals whilst keeping employees or patrons comfortable. The Workplace (Health, Safety and Welfare) Regulations 1992 states that: Isolate a radiator and slowly remove the bleed pin to drain the excess fluid into a container. Then remove the complete valve assembly from the radiator body to expose a ½” female BSP threading. Further fluid will be released at this point. Unique twist and dose adaptor that gives hands free dosing for the most difficult to access systems If a filling loop is fitted and accessible use Method 1 to dose via the filling loop stop valve, if not use Method 2 or 3 to dose via the radiator. Alternatively, use Method 4 to dose via the bleed valve if a Sentinel Eliminator or Eliminator TotalGuard filter is fitted. It is also possible to dose via an Eliminator Nano, but only if complete isolation is achievable. Close the filter valves and then slowly remove the adaptor from the filter, catching any excess fluid with a rag.Place a number 1 tablet and a number 2 tablet into the test tube provided. These are clearly marked. A filter will help capture debris, in a collection chamber, and hold it there until the chamber can be emptied.

Allow to stand for 10 minutes, shaking from time to time. The solution should change colour during this time. Unthread the 1/2” female BSP adaptor from the 1/2” male and then thread the male end into the radiator body. Use a spanner to carefully nip up the threads to ensure a water tight seal. a deeper yellow than or the same depth as the ‘Standard’ yellow band, the concentration of Sentinel X100 Inhibitor is satisfactory for system protection. Our dosing adaptor allows for four simple dosing methods. The adaptor also features our visible bullet, which prevents water from escaping the system and provides visible confirmation of dosing.Ideally, on the return pipe leading to a boiler. This is to stop debris entering the boiler and damaging it. We recommend that a filter is installed on all systems, in conjunction with a cleaning of the system, to capture any existing debris. Our range of cleaners is comprehensive and can be choosed based on the scenario that presents itself. See our cleaners and system cleaning-related products here. Isolate the filter from the system and remove the bleed pin from the valve at the top of the filter. Catch any excess fluid with a rag.

Close the radiator valves and then remove the adaptor from the bleed valve, catching any excess chemical in a container. Do you have a modern condensing boiler, especially a combi? (That combination makes a clean system really important as the very narrow waterways can clog quite easily, as I know to my cost.)Remove the adaptor from the system. The hose can be reconnected but should always be disconnected at one end to avoid the risk of any contamination of the fresh water supply. Once done, the wee Magna was refitted along with a dose of inhibitor as well as a dose of X900 - long-term cleaner. After 10 minutes have passed, place the tube against the white part of the shade chart provided. If the contents of the tube are:

When the chemical has completely emptied into the system (after ~ 30 seconds), the bayonet connection can then be released. Catch any excess fluid with a rag.Before performing the test, you should allow any Sentinel X100 Inhibitor that has been added to the system to circulate for a minimum of 15 minutes to allow the product to be evenly distributed. The following video shows the process: Close the radiator valves and then slowly remove the adaptor from the radiator, catching the excess chemical in a container. The horizontal, front facing filter is designed to be fitted in the most restrictive of spaces whilst delivering fantastic debris capture. a lighter yellow, add more Sentinel X100 Inhibitor to the system, allow to circulate fully and repeat the test. Sentinel's range of filters is crafted to fit any situation. The filters we offerrange from ultra-compact, where space is at a premium, through the compact Vortex300 and the larger Vortex500, which is also suitable for heat pump installations.