DEKS OLJE D1 1L

Product Information

Deks Olje D1 may soften some caulking. If in doubt consult us. The tannin’s and natural oils in woods such as Iroko impede the penetration and drying of finishes. These species of wood should be thoroughly prepared or allowed to weather for 12 months before applying Deks Olje D1.

Once the wood is saturated leave for 30mins and then wipe the surface to remove and excess oil with a rag that has been soaked in Deks Olje D1 and rung out so it’s damp. Channel Islands; Inflatable dinghy price on request Channel Islands; Flares not available to ship at this time Then, continue applying D1 ‘wet on wet’ until a uniform, overall saturation of the wood is achieved. The number of applications needed depends on the wood. If you have any boat varnish care tips or advice, please leave them in the comments below. We love hearing from you! Interior – Sand wood with 100 grit paper to open the pores, dust off and degrease the surface with methylated spirits.Please note that any materials soaked in Deks Olje D1 may catch fire if not discarded responsibly. Saturate the material with water after use, or place in a sealed water filled metal container before disposing as normal.

Clean all tools and equipment with white spirits while still wet. If allowed to dry, remove with paint stripper. Wipe up any drips or runs immediately with a cloth soaked in white spirits. Dried Deks Olje D2 may be removed with Dilunett. Store and maintain equipment as directed by the manufacturer.

If it’s an intense glossy look you are after we recommend you top-coat this product with the Deks Olje D2 Deks Olje D2 should only be applied to surfaces treated with Deks Olje D1 or previously finished with Deks Olje D2. Surfaces must first be clean, dry and free of all surface contamination. Clean and restore any Deks Olje D1 that has lightened to a gray finish, with Net-Trol, before applying Deks Olje D2. Wood already treated with Deks Olje D2 Deks Olje D1 is suitable for use on hardwood and softwood and has been specially developed for dense, oily and difficult to impregnate woods. It can be used on horizontal and vertical surfaces and provides protection against humidity and its effects as well as against damage from UV rays.

NOTE: If the surface looks mottled or splotchy after cleaning and sanding, Deks Olje #1 will still restore the appearance, but a few coats may be needed on the driest areas. Again, do not leave any Deks Oije #1 puddled on the surface. Coverage After stripping and cleaning, allow the wood to dry for 2-3 good drying days before applying Deks Olje D1. D1 may only be applied to bare wood surfaces or a weathered wood surface that was previously finished with Deks Olje D1. All other finishes must be completely and thoroughly removed first. If necessary sand the surface after cleaning and/or stripping (100 grit paper). New wood Wet sand the surface using 320 grit paper and Deks Olje D1 as the lubricant. Then wipe it over with a clean, dry, lint-free cloth and leave it to dry 24 hours. Apply 2 coats (minimum) or more of Deks Olje D2 to restore the finish. New full coat Owatrol offer 2 solutions for varnishing your boat. The first is by using our 2-step system of Deks Olje D1 and Deks Olje D2 and the second is using Linitop Yacht Vernis. D1 & D2

For more information on the overall care of your boat, take a look at our previous blog post, ‘ Top 10 Marine Care Products‘. Regular washing with Net-Trol will help to maintain the appearance of Deks Olje D1. It will gradually lighten over time due to exposure to the sun and UV rays. Repeat the re-coating process until the timber is fully saturated and will not accept any more finish.

Clean all tools and equipment with white spirits while still wet. If allowed to dry, remove with paint stripper. Wipe up any drips or runs immediately with a cloth soaked in white spirits. Dried Deks Olje D1 may be removed with Dilunett. Store and maintain equipment as directed by manufacturer.Wood that has weathered longer than 12 months should be cleaned with NET-TROL®* to remove all loose wood fibres, dirt and other surface contamination.