Zigbee 3.0 USB Dongle Plus, Zigbee Gateway EFR32MG21 + CH9102F Zigbee USB Stick for ZHA in Home Assistant, Zigbee2MQTT, Open HAB

Product Information

Also, from a chip perspective, I would like to be ready for Matter / Thread. The E version inspires more confidence in that regard, but I have nothing solid to prefer SI over TI. Home Assistant has “ZHA Device Handlers” and Zigbee2MQTT has “zigbee-herdsman-converters” which have similar concepts of converting non-compliant device attributes to follow Zigbee standards. You must also configure OpenHAB startup script to include /dev/ttyxyz for the USB adapter COM port as stated in the documentation: Serial Port Configuration | openHAB https://community.home-assistant.io/t/community-help-wanted-to-whitelist-all-compatible-zigbee-and-z-wave-usb-adapters-for-automatic-discovery-in-home-assistant-os/344412

Silicon Labs Simplicity Studio included "Flash Programmer" ( instructions) (can't find your device? read below!) First, you have to disassemble the device and pull the logic board out of its housing. You need a J00 Phillips screwdriver for this. Install official CP210x USB to UART Bridge VCP Drivers from Silicon Labs if using Windows or Mac → https://www.silabs.com/developers/usb-to-uart-bridge-vcp-drivers But the dBm is little hysterical then building on god system. If you is only having sleeping end devices and no routers yes its very good but if you you having good routers your mesh is working better having all sleeping end device connected to the routers and not the the coordinator.

EFR32MG1 Common Specs

However, if you are using the Zigbee2MQTT (Z2M) application instead of ome Assistant’s ZHA integration then know that Zigbee2MQTT software code for EZSP (EmberZNet Serial Protocol) support for Silabs based adapters is not yet mature and still listed as “experimental”. It is my understanding that they need more developers or testers actively working on their ezsp code in the zigbee-herdsman library that Zigbee2MQTT depends on. So, for now, Texas Instruments CC2652 and CC1352 based adapters is the way to go for a stable experience if use Zigbee2MQTT for “production” at home.

Debug 2022-08-31 08:16:45Received Zigbee message from '0x00158d000894fa97', type 'attributeReport', cluster 'msIlluminanceMeasurement', data '{"measuredValue":120}' from endpoint 1 with groupID 0 The WT32-ETH01 does not come without headers. which is a pain. anyone able to create a custom board with ethernet and an ep32 module? I then flashed the boot loader firmware and was able to load firmware from grobasoz/zigbee-firmware. Install drivers for Silabs CP210x (USB to UART Bridge VCP Virtual COM Port) if not already installed in the operating system, (and note reboot is required on Windows OS after install VCP driver). EFR32MG21 devices bring high performance, low power and secure solutions to the IoT. Designed to increase processing capability, improve RF performance and lower active current, EFR32MG21 devices are 2.4 GHz wireless SoCs optimized for line-powered Zigbee, Thread and Bluetooth mesh applications, including connected lighting, gateways, voice assistants and smart metering.

Rasp/CornBee is having one problem that all sleeping end devices like being connected to the coordinator and not to routers in the mesh that can being bad if the router part of the coordinator is not working so well (EEZSP ala "Sonoff bug" and Rasp/CornBee). Debug 2022-08-31 08:20:29lumi.sensor_motion.aq2: Processed data into payload {"voltage":3055,"battery":100,"device_temperature":25,"power_outage_count":61,"illuminance":187,"illuminance_lux":187}