Reolink PoE Security Camera 5MP Super HD with Human/Vehicle Detection, Support Audio Dome Outdoor Indoor Home CCTV Camera IP66 Waterproof IP Camera RLC-520A 2Pack

Product Information

A822, ALL, Argus, Argus PT, B500, B820A, C1 PRO, c1pro, C1-Pro, C2 Pro, C2-Pro, D800, Duo, Duo 2, Duo 2 Wifi, E1 outdoor, E1 pro, e1 pro PTZ, E1 pro sub, E1 Zomm, E1 Zoom, Inside, Other, RCL-410, RCL-410-5MP, rcl-420, RCL-510WA, rcl-511, RCL-520, rcl-522, RCL-810A, REOLINK C2, Reolink RCL-410, REOLINK RLC-423, reolink: rlc-410-5mp, Reolink-820a, rlc 410w, RLC 482a, rlc 510, RLC 520, RLC 842, RLC-1220A, RLC-410, rlc-410-5mp, RLC-410-5MP, RLC-410W, RLC-410WS, RLC-411, RLC-411WS, RLC-420, rlc-420-5mp, RLC-420-5MP-V2, RLC-422, RLC-423, RLC-423WS, RLC-510A, RLC-510AW, RLC-510WA, RLC-511, RLC-520, RLC-520-5mp, rlc-520a, RLC-522, RLC-542WA, RLC-810, rlc-810a, rlc-810c, RLC-811A, RLC-812A, rlc-820a, rlc822a, RLC-822A, rls-410s, RTC-410, RWC-511, w511 A brand new Reolink camera first needs to be connected to the network and initialized. During initialization, the credentials for the camera need to be set. To ensure you have the best latency possible, refer to the Reducing latency of motion events section. Asterisk (*) next to entities listed in this documentation

You may power on Reolink PoE cameras via PoE injector/switch or PoE NVR directly, or by using the power adapter.

There are several possible causes for Micro SD Card Not being Detected on Reolink App. You may follow the troubleshooting tips listed below to solve the problem. This integration creates a few camera entities, one for each stream type with different resolutions: Main, Sub, Ext, Snapshots Main, and Snapshots Sub. When the floodlight entity is ON always ON, when OFF controlled based on the internal camera floodlight mode (Off, Auto, Schedule), see the Floodlight mode select entity.

This issue is related to the function of the camera itself, and it is indeed a temporary workaround solution so that your camera can maintain the synchronization of audio and video. In some camera models, there is a delay of up to 5 seconds between the turn-off command and the sound stopping. The siren turn-on service supports setting a volume and a duration (no turn-off service call is needed in that case). Switch entitiesWhen using the siren turn-on service, the siren will continue to sound until the siren turn-off service is called. After plugging the new camera to the NVR, the camera's image does not show up on the monitor and it prompts "video loss". The following troubleshooting may be helpful to you. Solution: Please test the Micro SD card on your computer and see whether the Micro SD card can be read and written. If it doesn't, please use another Micro SD card to see if it works. The latency for receiving the events is the best for ONVIF push and the worst for fast polling, the fastest available method that is detected to work will be used, and slower methods will not be used.

Unsurprisingly, the Reolink RLC-520A shares the same design with the RLC-520 since it’s supposed to be a replacement for the older series. Step 4. Once the camera is installed, you can adjust the angle up down 70 degrees or 360 degrees horizontally. All these additional elements have made the RLC-520A a bit taller than the RLC-520, but, at its 4.13 x 3.74 inches (10.5 x 9.5 cm), it won’t really matter that much, especially since it will most likely end up being mounted outdoors. I am not entirely sure whether the extra-ruggedness was truly needed, but it’s definitely a welcomed addition. The IP66 rating is still there, so the camera will survive in case it’s targeted by powerful jets of water (powerful storms) and it’s also dust-proof. I doubt that you can put the RLC-520A on a pole, so it’s far more protected against lightning strikes than other devices, but I would still take all the necessary precautions to make sure your camera will survive a lightning storm (add some surge protectors).Follow the on-screen instructions to first setup the credentials (use the same credentials in Home Assistant). ONVIF push will result in slightly faster state changes of the binary motion/AI event sensors than ONVIF long polling. These models are discontinued and not sold anymore, they will continue to work with Home Assistant. To set up the camera, you need to connect the camera to a PoE switch/injector for network connection. After that, you may finish the initial setup via both Reolink App and the Client.