TENSOL 12 Acrylic Adhesive, 50ml Bottle/Perspex Bonding Glue Cement

Product Information

ANGLOSOL CEMENT 1200 is a ready-mixed, colourless, solvent based cement.It consists of acrylic polymer and methyl methacrylate monomer dissolved in solvents. for 3 to 4 hours at 80oC. Thermoformed, highly stretched components may be heated for 4 to 5 hours at

An alternative to a vice is a set of G-Cramps. These spread the pressure across the surfaces being joined, in much the same way as a vice. Notice the wood lengths that protect the ‘plastic’ and evenly distribute the pressure from the clamps. Once the adhesive has set the final bond strength can be increased by heat curing the material. This can Extraction and ventilation is vital. Tensol releases fumes, dangerous to inhale. The fumes can ignite under the wrong circumstances. For this reason, extraction / ventilation is vital. Wear suitable protective clothing. SW or AG grades and is not suitable for laminating sheets. Typical bond strengths are 24 MPa for a cold of the Part A. The Part A is a viscous mixture of acrylic polymer dissolved in monomer. The Part B is aTensol 70 is a two component, acrylic adhesive which hardens at room temperature by the polymerisation sheet can be used if it is suitably annealed prior to bonding. Tensol 12 must not be used with Perspex ME, Dispense the refrigerated cement directly into the joint using a suitable dispenser. It is best to do this in EVO-Stik TENSOL 70 is intended for cementing acrylic sheet to itself, but it will bond acrylic sheet to other materials such as wood. Applications include sign making, model making, structural engineering and acrylic sheet repair. Unsupported gaps of up to 1mm can be produced. EVO-Stik TENSOL 70 is not recommended for structural applications on aircraft. Mix Ratio (By Weight):

ANGLOSOL CEMENT 1200 should not be used for outdoor applications and cannot be used with Perspex ME, Perspex SW or Perspex AG grades.Nor is it recommended for laminating cast acrylic (Perspex) sheets as crazing will eventually occur. It is versatile, single part cement suitable for general fabrication work which does not need high bond strength, (usually for internal applications). ANGLOSOL CEMENT 1200 is suitable for joining items made from ‘Diakon’ acrylic polymers as well as cast acrylic (Perspex).Add Component B to Component A and mix thoroughly by stirring, taking care to entrap as little air in the adhesive as possible, after mixing cover the vessel and leave to stand for approx. 5 minutes to allow the larger bubbles to rise to the surface. assembly. After 4 hours cure the parts can be lightly machined but, for the best results, the joint should be The adhesive will be hardened sufficiently within one and a half hours to allow careful handling of the They should be left twenty four hours before taking out. This glue is very strong as it 'fuses' both

Thoroughly mix the adhesive by stirring, taking care to entrap as little air in the adhesive as possible. The Tensol 12 is designed for the bonding of cast acrylic sheet intended for interior use only. Extruded acrylicapplications, 1 to 2 weeks should be adequate. To obtain the maximum strength more rapidly the bond can perspex together permanently. Tensol cement is a type of glue called ‘dichlormethane methyl methacrylate’ and produces a chemical weld between two surfaces. The glue is applied to the surfaces to be glued and they are pressed together. They should be clamped for 24 hours and this gives a permanent joint.

Select an adhesive (Tensol), which joins plastics such as acrylic, together permanently. Tensol is also called ‘dichlormethane methyl methacrylate’ and produces a chemical weld between two surfaces. Tensol is applied to the surfaces to be glued and they are pressed together. The surfaces are clamped for 24 hours. Liquid solvent is applied using a brush or a syringe (often supplied with the glue). As it is a liquid, it is drawn along joints and surfaces through a process called capillary action. Care must be taken, as the glue damages exposed surfaces (as it melts the surfaces of the materials forming a ‘weld joint’). petroleum ether or white spirit then washed with water. Extruded or machined parts should be annealed Joints will be set sufficiently to be handled after 3 hours but must not be machined for at least 24 hours

Do not use adhesive that has been mixed for more than 20 minutes as it will be difficult to use and give Before using Tensol 12 store the adhesive at 5 to 10oC for 12 hours to reduce solvent evaporation between shrinks on curing allowance must be made for this when making butt joints and fillet joints. When bonding Tensol 70 is designed for bonding cast acrylic sheet. It will also bond extruded acrylic sheet, but will cause