Kenwood Multipro Compact Food Processor, 1.2L Bowl, 1.2L Thermo-resist Glass Blender, Dough Hook, Whisk, Reversible Slicing and Grating Discs, Spice Mill, 800 W, FDM302SS, Silver

Product Information

DO NOT touch the sharp blades. The blades and discs are very sharp, handle with care. Always hold by the finger grip at the top, away from the cutting edge, when handling the sharp cutting blades, emptying the bowl and during cleaning. If the food is too hard to push through the grid cook for approximately 10-15 minutes, then allow to cool in a refrigerator before processing. Keep hands and utensils out of the processor bowl and blender goblet whilst connected to the power supply. If food needs to be pushed down use a suitable utensil such as a spatula.

The maximum rating is based on the mini chopper/mill attachment that draws the greatest load. Other attachments may draw less power.The citrus juicer is not designed to be used with the Express Serve. Always use the citrus juicer with the main bowl. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH THE EUROPEAN DIRECTIVE ON WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) Screw the goblet onto the blade assembly. Refer to the graphics on the underside of the blade unit as follows: When making mayonnaise, put all the ingredients, except the oil, into the blender. Remove the filler cap. Then, with the appliance running, add the oil slowly through the hole in the lid. If you experience any problems with the operation of your appliance, before requesting assistance refer to the 'Troubleshooting Guide' section in the manual or visit www.kenwoodworld.com.

To blend dry ingredients - cut into pieces, remove the filler cap, then with the appliance running, drop the pieces down one by one. Keep your hand over the opening. For best results empty regularly. The whisk is not suitable for making all in one cake mixes as these mixes are too heavy and will damage it. Always use the knife blade. Whole spices retain their flavour for a much longer time than ground spices so it is best to grind a small quantity fresh at a time to retain the flavour. For non-rewireable plugs the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service). Always switch off the appliance and disconnect from the supply if it is left unattended and before assembling, disassembling or cleaning.

Manage your cookies

Baby food/purée - allow cooked food to cool down to room temperature before processing in the mill. Place the pulp remover into the filter drum - ensuring the tabs locate with the slots in the bottom of the drum.

Switch on and push down evenly with the pusher - never put your fingers in the feed tube. Process fully before adding more. Do not operate when using the Dicer or Discs without the slinger plate fitted. If the slinger plate is not fitted food will clog under the plate and not exit the food outlet, resulting in damage to your attachment. it has not been used commercially; you have not fitted a plug incorrectly; and you supply your receipt to show when you bought it. The cutting blades on the base of the filter drum are very sharp, take care when handling and cleaning the drum.

Where to Find your Model Number

Fit the sealing ring into the blade assembly - ensuring the seal is located correctly in the grooved area. If the plug or cord requires replacing a new cord set should be fitted by an Authorised Kenwood Repairer. Re-knead by hand only. Re-kneading in the bowl is not recommended as it may cause the processor to become unstable. Your processor is not suitable for crushing or grinding coffee beans, or converting granulated sugar to caster sugar. Use the pulse ( P) for short bursts. The pulse will operate for as long as the control is held in position.

Fit the required attachment/disc - do not apply excessive force. Refer to the Discs and Express Dice sections for further information, hints and tips. Fit the sealing ring into the blade unit - ensuring the seal is located correctly in the grooved area.Place the dry ingredients in the bowl and add the liquid down the feed tube whilst the appliance is running. Process until a smooth elastic ball of dough is formed.