The dirt malfunctions the heater blower and causes your Duraflame heater to make a noise. Solution: Use the remote from less than 20 feet distance from the front of the heater. And always use the remote pointing at the control panel of your heater. The design of the fireplace is perfect to heat large areas. Side windows allow for the “flames” to be enjoyed from all angles while effectively dispersing the heat in all directions. The use of infrared heating keeps the air warm without making it dry. This technology also helps keep the device from becoming too hot to touch, making it safe around children and pets. To get started, we simply attached the legs to the main unit, which comes entirely assembled and ready to go. We also needed to install the two included AAA batteries to run the remote. Besides, loose wiring, faulty temperature gauge, and heater cool-down cycle are responsible for your heater fan stopping working. Solution:

Be certain the plug fits tightly in the outlet. Heaters draw more current than small appliances. Overheating of the outlet may occur even if it has not happened with the use of other appliances. 10. Remote Control Is Not WorkingElectric fireplace inserts are a great way to turn your current fireplace into a cleaner, more energy-efficient operation. The inserts use the same technology as standard electric fireplaces, but they fit neatly into your home’s current fireplace. You can close up your flue, pop in the insert and enjoy remote-controlled “fires” after an easy installation. Plus, you may also discover your unit is creating noise when you turn on your heater. A beeping noise while turning on your Duraflame happens due to the dirty blower motor.

And in case of noise while shutting off or flaming on, replace the flame generator drive motor of the heater. Yet, if you find the problem remaining, then seek customer service from Duraflame. If you notice the “E3” is shown on the display, first visually inspect whether the air inlets and outlets of the heater are broken or not. If they are broken, the issue will cause overheating. To fix the overheating issue, clean the whole heater as well as the air filter and make sure enough airflow inside your heater. The Duraflame Electric Infrared Quartz Fireplace Stove with 3D Flame Effect has five different settings that you can easily manage on the device or with the accompanying remote. You can change the temperature and the flame settings so that you always have the best experience with your heater.The Duraflame remote control manual is given below in detail. You can now easily learn how to use a remote control: 1. Power Button Now you know all about the Duraflame heater operating instructions that include remote control operation, and most importantly Duraflame infrared heater troubleshooting guide. Yet, if you find the issue remaining, manually press the main power button of your heater. It will bring the solution. Duraflame remote control troubles may be noticed when the remote control is missing batteries or battery power. It may be because of the poor signal or your distance.

Already you know why your Duraflame heater not working and how to fix all the heater issues by yourself. Now let’s know how to operate your Duraflame heater with the remote control. 5. Error Code ER The remote control comes with a timer button. You can set your desired time from 30 minutes to 9 hours and by pressing “00”, you can turn off the time setting. Benefits Of Using Duraflame Infrared Heaters We Hope, by this process, your Duraflame heater will run normally. Duraflame Heater Operating Instructions If you find the heater display is showing “E1”, think, the possible cause is that the thermostat sensor of your heater is broken or disconnected. Solution: Now, your heater should run as normal. But if this procedure fails, don’t worry! You have an alternative way to reset your heater. Just go below & do the followings-

When you discover that your Duraflame heater not getting hot enough, be sure the main possible culprits are the faulty thermostat or blower motor and wrong ductwork installation. Solution: Duraflame 1500 Watt Infrared Quartz Cabinet Indoor Electric Space Heater With Thermostat And Remote Included In The Heaters Department At Com

If you look to disable or re-enable your heater function, you need to hold the power button for 10 seconds while ON. Showing the “E2” on the heater display means the thermostat sensor of the heater is broken. Solution: And the overheating causes the Duraflame e3 error code to show. Firstly unplug the heater and allow it about 3o minutes to cool down. Finally, you can try resetting your heater to fix the ER error code when you notice it on the display.The power button provides power to all of the functions of the Duraflame heater. The switch needs to be in the “ON” position for functions. But again pressing, you can turn off the heater. Below are the common Duraflame heater problems that you may face while using Duraflame infrared heaters and their simple solutions: 1. Heater Won’t Turn On A wall-mounted electric fireplace is ideal for anyone who’s after a more modern look. There are even electric fireplaces that are designed to be installed inside your wall for a recessed look.