So, to achieve the palest blonde possible, your hair should be a level 10 light yellow with a hint of gold. If your hair is light blonde mixed with a hint of orange, you’re at level 8, which will result in a pale, cool ash-blonde with T10. Mix the toner: Mix the Wella toner with the developer in a ratio of 1:2 in a plastic mixing bowl. You’ll use a 10 or 20-volume developer. If you are using 1 ounce of toner, mix it with 2 ounces of developer. Mix thoroughly with a tinting brush or whisk. Whether you left the toner on long enough. The amount of time you’ll need depends on how much brassiness you need to remove.

However, the result won’t be as light as it could be if your natural hair were at a level 9 or 10. If your hair is at a level 7, your results will turn out more of a dark ash blonde than a pale ash blonde. Koleston Perfect is always mixed with Welloxon Perfect to achieve outstanding colour results. After Treatment: using PH optimizes care products will enable better colour retention. The perfect partners for Koleston Perfect is INVIGO brilliant shampoo and INVIGO Post colour treatment. Warnings Toner can damage the hair by drying it out and making it more prone to damage. It also increases hair porosity, making your strands less adept at retaining moisture. Should You Get Your Toning Treatment Done Professionally? If it’s still brassy, put more toner on the section and let it process for 5 more minutes. Most people achieve their desired results within 30 minutes.

4. The Numbering System

The answer to this question is that it depends. The results you get with T10 hinges on three main things: Combine Koleston Perfect Deep Browns hair colour with Welloxon Perfect for outstanding results. Simple 1:1 mixing ratio. Apply the hair colouring mixture immediately with your chosen technique. We cannot guarantee accurate results with the use of any other developers. Regimen indications Professionals are also able to get their hands on the highest-quality toners and developers – ones that may not be available at your local beauty supply or department store. These products often provide better results overall and are gentler to your strands. When people talk about Wella toner, they are usually referring to the company’s permanent liquid toner line. These toners are color correctors that neutralize unwanted brassy tones in bleached or colored hair and deposit a new hue. If you have done everything correctly by (1) lightening your hair to the correct level, (2) applying the toner evenly, and (3) leaving it on long enough, your hair will be a silvery pale blonde. Those orange, yellow, or golden hues will also have disappeared.

For lift and colour in one: For super-blonde colour that lifts and tones, use Koleston Perfect Special Blondes; a range of high lift hues that should be mixed 1:2 with Welloxon Perfect. Use 9% developer for three levels of lift, and 12% for three to five levels of lift. 4. Start Where Grey is Most Prominent Do a strand test: Before toning all of your hair, do a strand test first. You want to make sure that you’ll be satisfied with the toner shade and that your hair and scalp won’t react poorly to the toner/developer mixture. Getting your toner professionally done may just be the best choice for you. Professional colorists have the training and experience necessary to choose the right toner shade and developer strength for your hair type, texture, and condition. Rinse thoroughly: Once you have achieved your desired toning result, rinse the toner out of your hair with lukewarm water. Using hot water will only accelerate the fading process.Apply to damp hair: Wet hair is a no-go for Wella toner. It’s best to apply the toner to damp hair so that the color can be easily distributed. If you’ll be washing your hair right before toning, towel-dry. The goal is to ensure that your hair isn’t dripping wet. Remember, though, the stronger the developer, the more damage it can do to your hair. So always go for the lowest effective developer strength if your hair has seen better days health-wise. Natural hair color exists on a spectrum, from level 1 to level 10. Level 1 is the darkest, and level 10 is the lightest your hair can get with bleach.

Wash your hair: 24 hours before applying the toner, wash your hair with a clarifying shampoo to remove any product buildup or oil from your hair. Product buildup can thwart your toning session, making it impossible for the toner to reach the surface of your hair, much less penetrate it. Also, don’t condition your hair, as this can affect the toner’s ability to penetrate the hair. volume developer: 10-volume developer is the gentlest option of the two, which makes it ideal for hair that’s already damaged or fragile. Just keep in mind that it won’t give you as much color payoff or longevity as a 20-volume developer would. Now that we’ve got the basics out of the way let’s talk about how your hair should look before applying your T10 toner. Wella recommends lightening your hair at least half a shade lighter than your desired final result before toning. That’s because the toner may darken your hair slightly. As well as choosing a hair lightener, finding the perfect product to cover regrowth is key. This is determined by the percentage of grey and your client’s desired look. However, if you leave the toner on too long, it can leave traces of blue or purple behind after shampooing. If this happens, you can use a clarifying shampoo or baking soda to remove it fast.There may be some moisture loss, split ends, and even breakage after bleaching any hair. Toning is not the best option if your hair is compromised in any way. Get Your Work Area Ready Use color-safe shampoo and conditioner: In the days and weeks after toning your hair, keep it looking fresh with a color-safe shampoo and conditioner.