Sadly the instructions do not mention any protections or what the mod will display in the case of a fault. How To Charge The Battery It is awkward to press when vaping as you have to hold the device with the mouthpiece horizontal, you also cannot see the LED indicators when vaping. What’s the most stylish vaping device on the market? Beauty is in the eye of the beholder, but we’d have to say that the lovely Innokin Sceptre deserves a good, long look. The Sceptre is Innokin’s solution for intermediate vapers who want a device that provides an upgrade in performance while maintaining the convenience and ease of use that have made pod systems famous throughout the vaping community. In fact the colour accent on the honeycomb makes it look like some of the paint has chipped off the mod. The main surprise for me was the coil life with this 0.5ohm coil.I always used the 1.2ohm coil in the original Sceptre pod and the coil lifespan was decent but not what I class as exceptional, but this 0.5ohm coil was exceptional.

But I did find that the pod was held in too securely a lot of the time as I had to use my teeth to grip the mouthpiece to pull the pod out to fill. There is nowhere to grip on to! PodThe Innokin Sceptre 2 pod kit is an ideal choice for new and experienced vapers who prefer a discreet device that creates a small amount of vapour. This small and dependable vape is powered by a 1400mAh battery that will deliver up to 20W of power. There is a Sceptre 2 refillable pod included with each kit and is pre-installed with a 0.6 Ohm S Coil, which allows for an RDTL (Restricted Direct To Lung) vape.

I found that a good MTL airflow was obtained with the airflow slider in the mid position for me. Does It Leak? If your Innokin Sceptre is gurgling, the most likely reason is that you’re using too much air pressure when vaping with the device. That’s particularly likely to happen if you’re using the 1.2-ohm mouth-to-lung coil and have the airflow dial turned to the MTL setting. If you puff harder in an attempt to get bigger clouds out of the device, you’ll overwhelm the pod’s capacity to manage airflow and will draw excess e-liquid into the atomizer coil assembly and chimney. The e-liquid caught in the pod’s chimney creates a gurgling sound and may even enter your mouth if you continue puffing too firmly. Always puff gently when using the Innokin Sceptre. If you’re not happy with the device’s vapour production, you can increase the wattage, increase the airflow or switch to the 0.5-ohm coil. Innokin Sceptre Leaking Charging took a few minutes either side of 2 hours every time with a 2A charging plug. Obviously the charger output is reduced to match the capability of the mod. How To Fill the Pod A manual fire button is provided but this device also has an auto draw system meaning you can simply inhale on the mouthpiece and the device will fire. Use a certified wall charger with a high quality microUSB, such as the cable provided with your Innokin Sceptre.I found in the standard power mode this did perform well but felt like it needed slightly more “ ooomph“. I found using a 1A charging plug it took just over 2 hours (2 hr 8 mins) to fully charge the battery. How To Remove the Innokin Sceptre Pod On the MTL setting with the 1.2ohm coil I find the airflow perfect. Even with the auto draw activation – it is quite a tight airflow but not the tightest I have used. You can pretty much close off the airflow completely. There is a slight airflow – enough to trigger to auto draw fire but that is about it.

It is worth noting I have had building work going on at home and been using this kit. I dropped it multiple times and it’s still going strong. The only bruises it has to show for the rough treatment is some scratching to the body. The Innokin Sceptre replacement coils have been designed for use with the Innokin Sceptre pod kit and Innokin Sceptre Tube kit. There are two versions of this coil available, to support mouth to lung vaping and restricted direct to lung vaping. Both versions of this coil will work best with a high PG e-liquid that's 50% PG or higher.The 5-ohm mesh RDL coil works at 18 or 20 watts and is designed to deliver a restricted direct-to-lung hit with lower-nicotine e-liquids. I was very impressed with the power regulation, even down to the last few vapes before the battery died there was no loss of power! Change power level – turn off the device and hold the power button in. The lights above the button will change colour. The green light is the standard power level and the purple light is the boost power mode. Release the power button when the light illuminates for the power mode you want. It will cycle between both power modes when you hold the button down.