Vallejo for me too. Long, thin applicator that doesn't dry out (so far - 11 months) and a putty that you can blend in with a damp finger meaning MUCH reduced sanding afterwards which is great because I'm so lazy! I have gotten where I only use this putty for small, non load-bearing seams that don't require any re-scribing, such as canopy to fuse, where you don't want to sand at all or little. Add 1/2 cup (120 ml; 4 fl oz) of water and stir until the mixture is completely smooth. You’ll need an equal mixture of glue and water to get the perfect silly putty, so measure out 4 oz (120 ml) of water and pour it into the bowl. Then, use a spoon, fork, or whisk to stir the glue and water together until they’re completely blended. Dissolve 1/2 tsp (4 g; 0.14 oz) of Borax in 1/4 cup (60 ml; 2 fl oz) of hot water. Scoop out about 1/2 tsp (4 g; 0.14 oz) of Borax powder and add it to 1/4 cup (60 ml; 0.14 fl oz) of hot water in a small cup or bowl. Then, stir the mixture vigorously with a spoon until the Borax granules have dissolved.

Big Boy Plastic Flexi Filler 250ml | Toolstation Big Boy Plastic Flexi Filler 250ml | Toolstation

Pour the dissolved Borax into the glue mixture and stir it together. When you start stirring all of the ingredients together, you’ll see them reacting almost immediately. At first, it will look like the glue is clumping together, but keep stirring until you get a ball of putty with a relatively even consistency. Let the glue dry for about 1 day. Put the plastic lid somewhere that it won’t be disturbed, like on a countertop or your desk. Leave it alone for a whole day; otherwise, it might not dry correctly. [11] X Research source Pour a small amount of water into the center of the well. Since plaster absorbs moisture from the environment, the exact amount of water you’ll need for this will vary. Start by adding about 1–2 US tbsp (15–30 mL) of room-temperature water to the center of the well. If the mixture seems too dry when you mix it together, you can add more water. [5] X Research source A lot of people say they like Deluxe's Perfect Plastic Putty, so I thought I'd try it. I took off the cap, added the long tapering applicator, and squeezed some out and used it. Then I put a plastic cap over the end of the applicator to stop it drying out. You can even keep your putty in a plastic egg if you want it to seem more like store-bought silly putty!I use the tip of a scalpel, just as with green and white stuff to apply it. If you get any drying out at the top of the tube and the material becomes too dry to work in, just add a couple of drops of water and give it a few minutes to rehydrate. This article was co-authored by wikiHow staff writer, Amy Bobinger. Amy Bobinger has been a writer and editor at wikiHow since 2017. She especially enjoys writing articles that help people overcome interpersonal hurdles but frequently covers a variety of subjects, including health and wellness, spirituality, gardening, and more. Amy graduated with a B.A. in English Lit from Mississippi College in 2011 and now lives in her hometown with her husband and two young sons. The putty should tear or snap if you pull it sharply, so it’s easy to use just a small amount for your project! Pour 4 oz (120 ml; 4 fl oz) of non-washable school glue into a bowl. Silly putty is stretchy, bouncy, and fun, and it’s super easy to make! To start, measure out about 1/2 cup (120 ml; 4 fl oz) of school glue into a medium-sized plastic bowl. For the best results, use non-washable glue. However, you can use white, clear, or even glittery glue if you like! [1] X Research source

Deluxe Materials Perfect Plastic Putty 40ml - Hobbies Deluxe Materials Perfect Plastic Putty 40ml - Hobbies

Use the putty within 45 minutes. To use your putty, press it into a hole in the wall, then scrape it to create a smooth, flat surface, and let it dry. When it’s completely hardened, sand away any bumps, then paint over the plaster and enjoy your handiwork! [8] X Research source

Pour a handful of plaster onto the tray and make a well in the center. The measurement for this doesn’t have to be exact, but you’ll probably need about 1/4 cup (50 g) of the basecoat plaster. It will be easier to mix on a flat surface, so pour the powder in a pile on the top of a plastic paint lid or a similar tray with slightly raised sides, then use your finger to make a dip in the center of the pile. [4] X Research source For anything that has to be strong or shaped or scribed over, I use CA adhesive, worked while as "green" as possible after drying. I tried using the applicator the first time I tried using the perfect plastic putty. Since the instructions mentioned washing applicator out after use, I though that was quite a waste!