TOPPING MX5 Headphone DAC Amplifier Class D Power Amp 70Wx2 NFCA 1600mWx2 USB/OPT/COAX/Bluetooth/TRS/RCA Input Desktop Home Audio Decoder 384kHz/DSD256 with Remote Control (Black)

Product Information

Lets say MX5 was last used on USB input before entering standby, then signal is provided on optical input, I understand MX5 will turn on automatically but will it switch to optical or do you have to switch source manually from last used (USB) to the one currently providing signal (Optical) ? I can read it but I cannot understand what to do. I have tried but failed a number of different attempts. I have also managed to get it into some mode that is undocumented, which says "dFU" and you cannot do anything with the device, apart from unplug it and insert the plug again to get it working. In addition to supporting various digital inputs, MX5 also supports fully balanced TRS and single-ended RCA analog inputs. Greatly expand the scope of application. USB/OPT/COAX 6.0dB (Vrms/FS) @G=L 19dB (Vrms/FS) @G=H | SE -0.2dB @G=L 13.6dB @G=H | BAL -6.1dB @G=L 7.6dB @G=H

With the help of Infineon Merus Class D amplifer, MX5 can output 70Wx2 under 4 ohm load 10% distortion, 55W x2 under 4-ohm load 1% distortion. Under 8-ohm load, 10% distortion can output 42Wx2, and 1% distortion can output 35W x2, which can meet daily use. For analog signals of different strengths, MX5 provides three options of sensitivity to ensure that the signal can be accurately detected, which greatly expand the scope of application.Itt még egy dolog van, amire érdemes figyelni. A Topping MX5 képes az APTX HD szabványú kapcsolatra, ami egy nagyon jóminőségű vezetékmentes kapcsolat. Mondhatjuk, hogy a megfelelő feltételek teljesülése esetén teljesen kiválthatja a kábeles kapcsolatot. Így aztán érdemes odafigyelni arra, hogy a telefon, amiről a zenét szolgáltatjuk, szintén tudja ezt a szabványt, mert így tényleg kivételes minőségben tudunk majd zenét hallgatni, ha mondjuk egy Tidal a forrás. Márpedig a forrás természetesen Tidal volt.

The only problem I have noticed is that the amp gives out *lots* of RFI over the speaker cables whenever they are in use. No problem when in headphone only mode. Surprisingly the big power supply seems OK. I am a ham radio operator and I could see so much RFI on 40m and 20m that I could actually hear the song being played in AM mode. Some hefty torriods on both speaker cables fixed that mostly. The carrier is still there but the modulation is all but gone so if I want serious DX I need the turn the amp off - or get more torroids. A készülék beüzemelése nem túl bonyolult dolog, kiváltképp ha fejhallgató erősítésére használnánk. Ekkor csak csatlakoztatnunk kell mondjuk a laptopunkhoz (bár ez sem muszáj), felcsavarnunk rá a Bluetooth antennát és áram alá kell helyeznünk. A tápegysége kívül van, annak elrejtéséről tehát még gondoskodnunk kell. Ha megelégszünk a Bluetooth kapcsolattal, akkor akár a fejhallgató csatlakoztatása után lőhetjük is rá mondjuk a mobilunkról a zenéket. Records the default button state of the corresponding category & the status of CCPA. It works only in coordination with the primary cookie. On my D30, You hold the front knob in while you turn the power switch on. Release the knob. Then rotate it through the menu, pushing to select. Someone correct me if I'm wrong but I think the general consensus here at ASR would be that in terms of DAC & amp quality the differences shouldn't really be audible since both measure with noise, distortion etc. in the inaudible to human ear range. So going for the more suitable feature set would seem to make sense.

The MX5 has an NFCA circuit with ultra-low noise and distortion. It pairs with high-sensitivity IEMs and power-hungry high-impedance headphones perfectly.

MX5 provides two custom setting memories, C1 and C2. Long press can memorize the current input selection, output selection, volume setting, bass setting, treble setting, and gain setting. And short press to call out in subsequent applications. It greatly facilitates your use. The woofer was developed to fit in a commercial speaker, but was instead sold out to the public. It is quite beefy 5" weighing in at 1,5kg. First time I have had a desktop amp that does well on *both* headphones and speakers. For the last 3 years I have been using a SMSL AD18 - which the MX5 has just replaced. I was never impressed with the USB DAC on the AD18... It did a fine job of amplifying analogue signals but I found it quite poor when decoding audio from USB at any resolution. The real killer was I had begun experiencing loud random white noise episodes at 96Khz. I thought this may be an issue with my new laptop and/or Windows 11 but apparently it is known thing with the AD18 on prior versions of Windows too. Guess I had not used the USB interface at high resolution much.MX5 supports users to adjust the treble and bass. The treble and bass provide adjustable ranges from -10dB to +10dB respectively. A számokat meghallgattuk hangfalakon és fejhallgatón egyaránt. A hangfalak a második rendszerünk hangsugárzói voltak, nevezetesen egy pár Jamo Concert 8SE. Ezeket most behoztuk az íróasztal mellé és bár így messze nem volt ideális a környezet, de a végeredményt tekintve nem kizárt, hogy hosszabb távon itt is maradnak. Offering a world class service to our customers, we are a highly focused team who can be trusted to support you The EX5 is normally higher price than the MX5. If you can have them at the same price, the EX5 would probably be the safer bet due to the noise issues and such many are having with the MX5. Otherwise sound quality should be great with both. The limited kind of tone controls stereo amps have never appealed to me, but that's of course subjective.