I have four UAP-AC-IW deployed in our office and setup with the Unifi Controller. Wireless access to the outside world works great. All wireless devices can see one another. However, wireless devices cannot see wired devices on our network. I have two vlans configured in the Edgerouter (2001 and 2002). In UniFi I used these for a guest and a tenant wifi. The last one should only be accessable on the Basement AP, which is directly connected to the ERX.

Spectrum has installed a new modem and router. UAP Lite are connected to the router via POE modules. I think one is working – not sure, and the other is not working. You shouldn’t have to worry about the channels, just leave in on auto and the Unifi controller will work it out. But that isn’t your real problem. When a device connects to and wireless network but can’t access the internet and a few thing can be the issue: I was hoping to automatically switch to the secondary WAN port which will route to the radios if my Internet connection failed. It did not work. Thank you Rudy! I have a cabled connection to a remote area of my property but the WiFi does not reach there, so if plugging in an UAP-LR there will extend the WiFi, that’s really all I need. I am unable to get my Xbox One/One S to connect to the Wireless. All other devices, SmartTv and iPhones can connect.Basically I use my computer and my smart tv hooked up right now only to my edgerouter 4 max this product

My metal shop is 100 yards from my house router and whenever I enter I lose signal. Is there an inexpensive way to boost the signal inside my shop? For in-house placements, the UniFi 6 Lite and the Long Range models are most of the time the best fit. To determine where to place the Access Point you need to keep in mind that the Unifi Access Point has a doughnut shape coverage with the Access Point in the middle.Really hard to say from here. Are both devices place at the same location? Unifi Acces Points are based placed on the ceiling, instead of mounted to a wall. That could make a difference. Apart from the device, if there is a 20cm concrete wall between the access point and the measured location, then no access point will be able to give you a good wifi strength. I continually get a certificate error message in both IE and Chrome when I try to load the controller. What’s the fix for this issue? I have changed firewall and antivirus settings as noted, but still no go. There are 4 main methods to resetting a UniFi Access Point: UniFi Physical factory reset, UniFi Controller factory reset, UniFi Debug Terminal Window Reset, and UniFi SSH factory reset. UniFi Physical Factory Reset if they ever spec it out ,then maybe , seems its “after thought device to me” to answer “way are WAP so hard to setup, home users.” UAP-AC-LR เป็น Long Range Wireless Access Point ที่ให้ความสามารถในการใช้งานสัญญาณ WiFi 5 ระดับมืออาชีพ ทำให้คุณสามารถเชื่อมต่ออินเตอร์เน็ตแบบไร้สายได้แม้ในพื้นที่ที่มีการใช้งานเครือข่ายหนาแน่นอย่างเช่นออฟฟิศหรือโรงแรม

Depending on your floor type you will need one for every floor or you can do with just one Access Point on the first floor or ground floor ceiling. If you have wooden floors, you could start with just one Access Point. Place it in a central location without any obstruction for the best coverage. When you have concrete floors, you will need to install an Access Point on every floor for decent coverage. The rebar and concrete weaken the signal too much for good coverage. You can better spend your money on one LR for the ground floor and add AC-lite’s where necessary (upstairs for example)Hi I´m having some problems with my unifi setup, I have an 4 port poe switch but 5 AP´s and an cloud key, so i got an poe Injector (adapter) for the 5th AP, but the 5th AP always comes up as “isolated” could that be fixed by setting up the 5th AP without the cloud key? Next, we need to install the Unifi AP, make sure it’s connected with an ethernet cable to your network. When the led is solidly white, you know that the AP is connected and in the factory default state.